Dialogic Brooktrout Digital Board Spezifikationen PDF herunterladen

Installing the

Dialogic® Brooktrout®

TR1034

Digital / Ethernet

Fax Board (Single Span)

Part Number: 931-101-05

The Dialogic

® Brooktrout® TR1034

Digital/Ethernet combination PCI fax boards

(“TR1034” or “TR1034 Fax Board(s)”) are full-sized,

single slot, PCI bus compatible boards with T1/E1,

Ethernet, and H.100 capabilities. The TR1034

delivers 33.6 Kbps (V.34) fax transmission speeds,

up to 30 fax channels per fax board, Adaptive Call

Progress, Error Correction Mode, MMR fax

compression, and an onboard T1/E1 interface (see

Figure 6). The Ethernet connector is used for T.38

Fax over IP.

The Dialogic® Brooktrout® TR1034 Fax Board has

access to off-board resources using the H.100 bus

interface. Using a bus adapter (available

separately), the H.100 can interoperate with an

MVIP or SCbus interface.

You need a separate fax application to use the

TR1034 Fax Board. Please contact your application

provider for the correct operating system driver,

supporting files, and firmware.

Operating/Environmental Specifications

This device must be installed in an enclosure that

meets the following electrical and mechanical

requirements.

 Power requirements:

Base: 4 A at 5

VDC = 20 W

Base + Mezzanine: 5 A at 5 VDC = 25 W

 Temperature: 0°C - 50°C

 Humidity: 10% - 95% (noncondensing)

 Cooling: Direct forced-air flow is required.

 33 MHz PCI 2.2 Universal card (3.3/5V

signaling)

Setting the Module Number (SW1)

You must set each TR1034 Fax Board to a unique

module number to identify the resources associated

with a specific board in a multi-board system. SW1

(Figure 1) is a rotary switch (see location in

Figure 4). Use it to set the module number for each

TR1034 Fax Board. The available settings are 2 - F

(0 and 1 are reserved).

Figure 1 Rotary Switch - SW1

Using the H.100 Termination Switch (SW2)

On a single TR1034 or on multiple TR1034 Fax

Boards installed in the same chassis, leave SW2 in

the OFF position. See Figure 4 for its location.

Multiple TR1034 Fax Boards in the same system do

not require the use of a connecting H.100 cable.

If you have a TR1034 and other boards that need to

be connected using an H.100 cable (not supplied),

you must terminate the H.100 clock signal. Only the

boards at each end of the cable must be terminated.

All other boards must not be terminated (see

Figure 2).

Figure 4 Dialogic® Brooktrout® TR1034 Digital/Ethernet

PCI Fax Fax Board

Figure 2 Setting Clock Termination in a Series of Boards

Connected by an H.100 Bus

SW2 (see Figure 3) controls termination for the

H.100 clock signals. Set the switch to ON to

terminate the H.100 clock on a TR1034 Fax Board

(see Figure 4 for the location of the switch on the

board). The SW2 LED lights when SW2 is set to the

ON position.

Figure 3 SW2 - H.100 Clock Termination Switch

Installing the Dialogic® Brooktrout® TR1034

Fax Board

To install the board:

1. Power off the computer.

2. Remove the computer cover. If the system has a

board hold-down bar, remove it as well.

3. Locate an unused PCI expansion slot and

remove the blank bracket.

The TR1034 Fax Board comes with an extension

bracket that allows it to fit snugly into an ISA

form-factor chassis. If you have a PCI

form-factor chassis, use a Phillips-head

screwdriver to remove the extender bracket (see

Figure 4).

4. Holding the TR1034 Fax Board at each top

corner, insert the board firmly into the PCI slot,

sliding the extender into the side of the chassis,

if necessary.

5. Screw the board’s mounting bracket securely to

the computer's frame. See Figure 4.

6. Attach the connector on the H.100 cable to the

connector on the board, if needed.

7. Replace the computer cover.

8. Turn on the computer.

The board status LED (see Figure 4)

continuously flashes yellow when you turn the

computer on.

Note: Dialogic® Brooktrout® fax boards should not be

present in the computer during the installation of any

operating system. The operating system can

misinterpret the board as being some other device, with

unpredictable consequences.

Recognizing PCI Slots

The PCI connectors in the computer chassis usually

appear as white slots. The different variations of

PCI connectors that can be used with the TR1034

Set the H.100 switch

to the ON position.

Set the H.100 switch

to the ON position.

Set H.100 switches

on these boards to

the OFF position.

Push switch

toward board

to turn ON.

Caution: A small amount of static electricity can

destroy the sensitive components on your board.

To prevent static damage, always connect yourself

to ground using a ground strap before touching a

circuit board. Handle boards only by the edges or

metal mounting brackets and transport boards in

an anti-static bag.

Warning: When installing the board, be sure that

the mounting bracket is securely fastened to the

chassis and the chassis is plugged into a

grounded three prong plug. Improper chassis or

bracket grounding can result in harmful or fatal

electrical shock as well as component damage.

SW2 - H.100 Termination Switch

SW1 - Rotary Switch

Mounting Bracket

T1/E1 Connector A

T1/E1 Status LED A

Board Status LED

D23 - Termination Switch Indicator LED

H.100 Connector

Universal PCI Connector

ISA length chassis

extension bracket

These LEDs are for manufacturing purposes only.

LEDs

1 2

Inhaltsverzeichnis

Seite 1 - Fax Board (Single Span)

Installing the Dialogic® Brooktrout® TR1034 Digital / Ethernet Fax Board (Single Span)Part Number: 931-101-05The Dialogic® Brooktrout® TR1034 Digital/

Seite 2 - T1/E1 Status LED

Weitere Dokumente für Vernetzung Dialogic Brooktrout Digital Board

Um das Dokument anzuzeigen Dialogic Brooktrout Digital Board Spezifikationen

Dialogic Brooktrout Digital Board Spezifikationen (2 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Dialogic Brooktrout Digital Board Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Vernetzung Dialogic Brooktrout Digital Board herunter. Dialogic Brooktrout Digital Board Specifications Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Vernetzung Dialogic Brooktrout Digital Board

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Dialogic Brooktrout Digital Board