Dialogic DSI SS7MD Bedienungsanleitung Seite 126
- Seite / 176
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
126
Chapter 6 Command Definitions
Attributes
None
Examples
STC7P;
Output Format
CCS SS7 Signalling Link Status (Page 1 of 2)
C7LINK LS EQU TS SNLINK L2 STATUS L3 STATUS
1 1 1-3 1-3-16 BLOCKED
2 1 1-4 1-4-16 IN SERVICE AVAILABLE
3 2 3-3 3-3-16 INITIAL ALIGN UNAVAILABLE
4 2 3-4 3-4-16 OUT OF SERVICE DEACTIVATED
EXECUTED
CCS SS7 Signalling Link Status (Page 2 of 2)
C7LINK L2 STATE L3 STATE L3 BLOCKING STATUS
1 BLOCKED ---- ---- ---- ---- ---- ---- ----
2 IN SERVICE AVAILABLE ---- ---- ---- ---- ---- LIIP ----
3 INITIAL ALIGN UNAVAILABLE ---- ---- ---- ---- ---- ---- ----
4 OUT OF SERVICE DEACTIVATED ---- ---- ---- ---- ---- ---- ----
EXECUTED
6.14.6 STDDP – Status Disk Drive Print
Synopsis
This command displays the status of all hard disk drives within the RAID array.
Note: This command is not available for the Dialogic
®
DSI SS7G21 and SS7G22 Signaling Servers.
Syntax
STDDP;
Prerequisites
None.
Attributes
None.
Example
STDDP;
Output Format
STDDP;
Disk Drive Status
DRIVE STATUS
0 UP
1 UP
EXECUTED
The STATUS field will display one of the following values:
• UP – The disk drive is operational. If the disk forms part of a RAID array then all the RAID devices on this
drive are in an 'active sync state'.
• DOWN– The disk drive is non operational. If the disk forms part of a RAID array then one or more of the
Raid devices on this drive is faulty.
• RESTARTING – One or more of the raid devices on this drive is synchronizing with another Raid device.
The disk is considered 'non operational' until synchronization is complete.
- Dialogic 1
- DSI Signaling Servers 1
- Copyright and Legal Notice 2
- Publication Date: August 2008 2
- Document Number: 05-2304-005 2
- Contents 3
- Revision History 8
- Chapter 1: Overview 9
- Chapter 1 Overview 10
- Chapter 2: Specification 17
- 2.3.2 Dialogic 19
- Chapter 2 Specification 20
- Chapter 4: Operation 27
- Chapter 4 Operation 28
- Are you sure? [Y/N] 29
- CNSYS:SECURE=Y; 31
- 5.3.2 MTP3-Specific Timers 47
- Table 6. MTP3 ITU Timers 47
- Table 7. MTP3 ANSI Timers 47
- ALCLS:CLA=,CODE=…; 50
- ALCLS:CLA=3,CODE=20; 50
- ALCLP[:CLA=]; 50
- CNMOI:C7LINK=,STS=,RTS=; 58
- CNMOE:C7LINK=; 58
- CNMOE:C7LINK=1; 58
- CNPCC:PCM=1-1,SYNCPRI=3; 62
- CNPCE:PCM=; 62
- CNPCE:PCM=1-1; 62
- • The RDC is blocked 64
- OFFSET value to take effect 70
- CNUSC:USER=3,AUTH=SHA; 75
- CNUSE:USER=; 75
- CNUSE:USER=3; 75
- CNXCI:OTS=,ITS=,[DUPLEX=]; 77
- CNXCE:OTS=,[DUPLEX=,]; 77
- CNXCE:OTS=1-1-16; 77
- C7LSE:LS=; 80
- C7LSE:LS=1; 80
- C7RTC:C7RT=1,NC=1,LS1=2; 82
- C7RTE:C7RT=,NC=; 82
- C7RTE:C7RT=1,NC=1; 82
- IPEPS:ETH=1,SPEED=100; 86
- IPEPS:ETH=4,IPADDR=STANDBY2; 86
- • MMPTP - MML Port Print 89
- • MMLOP - MML Log Off Print 89
- • MMLOS - MML Log Off Set 89
- • MMPTC - MML Port Change 89
- Attributes 91
- Examples 91
- Output Format 91
- Chapter 6 Command Definitions 100
- RDC1=1,LABEL=ALARM; 102
- RDCRE:RECORD=,[DISCARD=Y]; 103
- RDCRE:RECORD=1; 103
- SGDPI:DEST=1, RAS=1; 108
- SGDPI:DEST=,RTPRI=,[LABEL=,]; 108
- SGDPI:DEST=,RAS=,[LABEL=,]; 108
- SGDPC:DEST=1, RAS=1; 109
- SGDPE:DEST=; 109
- SGDPE:DEST=1; 109
- SGDPP:[DEST=]; 109
- SGIRC:IR=1,DEST=5; 111
- SGIRE:IR=; 111
- SGIRE:IR=1; 111
- SGIRP:[IR=]; 111
- SNALI:RAS=,SEQ=,SNLINK=; 114
- SNALI:RAS=1,SEQ=1,SNLINK=1; 114
- SNRAE:RAS=; 116
- SNRAE:RAS=1; 116
- IPADDR2=192.112.111.123;; 119
- SNSLC:SNLINK=1, PPORT=2905; 120
- SNSLE:SNLINK=; 120
- SNSLE:SNLINK=1; 120
- STIPP:IPADDR=173.132.23.3; 128
- IP Status 128
- EXECUTED 128
- • Status 133
- • Stratum 133
- • Offset 133
- 193.145.185.151 135
- 173.132.73.122 135
- 173.132.73.21 135
- 193.145.185.149 135
- Signaling 137
- 193.145.185.154 138
- SGDPI:DEST=2,RTPRI=MTP; 141
- • itself 143
- • an IP address of 0.0.0.0 143
- 194.192.185.11 145
- 192.195.185.11 145
- 192.195.185.12 145
- 194.192.185.12 145
- RESET=Y,LABEL=C7LINK; 158
- RDPDE:REPORT=1,C7LINK=3; 158
- 194.192.185.111 166
- 195.193.185.12 167
- 195.193.185.11 167
- 195.193.185.111 167
- 11.3.2 SG 2 Configuration 168
- STTPP command 169
- Chapter 13: Command Summary 171
- Chapter 13 Command Summary 172
- Glossary 175
- Chapter 14 Glossary 176
Verwandte Produkte und Handbücher für Vernetzung Dialogic DSI SS7MD
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern