Dialogic DSI SS7MD Bedienungsanleitung Seite 92
- Seite / 176
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
92
Chapter 6 Command Definitions
6.9 Maintenance Commands
The maintenance commands include:
• MNBLI - Maintenance Blocking Initiate
• MNBLE - Maintenance Blocking End
• MNINI - Maintenance Inhibit Initiate
• MNINE - Maintenance Inhibit End
• MNRSI - Maintenance Restart System Initiate
6.9.1 MNBLI – Maintenance Blocking Initiate
Synopsis
This command initiates blocking for boards, signaling links, remote data centers, SIGTRAN links and
SIGTRAN Application Servers. A blocking command removes from use the board, link, route or server
covered by the command, it also removes their configuration data from the lower levels of the Signaling
Gateway and only configuration management maintains knowledge of their existence.
Possible grouping are:
• SS7 signaling links
• Boards
• Remote Data Centers (RDCs)
• SIGTRAN signaling links
• SIGTRAN Remote Application Servers
If the grouping being blocked is already in the blocked state, no action is taken.
If a C7 link has been inhibited, the inhibiting is removed as part of the blocking action.
Syntax
MNBLI:C7LINK=…;
MNBLI:BPOS=…;
MNBLI:RDC=…;
MNBLI:SNLINK=…;
MNBLI:RAS=…;
Prerequisites
• The item being blocked has been initiated.
• When blocking a board, all SS7 links on the board must already be blocked.
• If this is the last RDC to be blocked, then it cannot be blocked until all continuous records and periodic
reports are ended.
• An SNLINK of SNTYPE M2PA can only be blocked if its associated C7LINK is either blocked or inhibited.
Attributes
CONFIG,PROMPT
Examples
MNBLI:SNLINK=12;
MNBLI:C7LINK=4;
Output Format
Blocking C7LINK 1
Blocking C7LINK 2
EXECUTED
- Dialogic 1
- DSI Signaling Servers 1
- Copyright and Legal Notice 2
- Publication Date: August 2008 2
- Document Number: 05-2304-005 2
- Contents 3
- Revision History 8
- Chapter 1: Overview 9
- Chapter 1 Overview 10
- Chapter 2: Specification 17
- 2.3.2 Dialogic 19
- Chapter 2 Specification 20
- Chapter 4: Operation 27
- Chapter 4 Operation 28
- Are you sure? [Y/N] 29
- CNSYS:SECURE=Y; 31
- 5.3.2 MTP3-Specific Timers 47
- Table 6. MTP3 ITU Timers 47
- Table 7. MTP3 ANSI Timers 47
- ALCLS:CLA=,CODE=…; 50
- ALCLS:CLA=3,CODE=20; 50
- ALCLP[:CLA=]; 50
- CNMOI:C7LINK=,STS=,RTS=; 58
- CNMOE:C7LINK=; 58
- CNMOE:C7LINK=1; 58
- CNPCC:PCM=1-1,SYNCPRI=3; 62
- CNPCE:PCM=; 62
- CNPCE:PCM=1-1; 62
- • The RDC is blocked 64
- OFFSET value to take effect 70
- CNUSC:USER=3,AUTH=SHA; 75
- CNUSE:USER=; 75
- CNUSE:USER=3; 75
- CNXCI:OTS=,ITS=,[DUPLEX=]; 77
- CNXCE:OTS=,[DUPLEX=,]; 77
- CNXCE:OTS=1-1-16; 77
- C7LSE:LS=; 80
- C7LSE:LS=1; 80
- C7RTC:C7RT=1,NC=1,LS1=2; 82
- C7RTE:C7RT=,NC=; 82
- C7RTE:C7RT=1,NC=1; 82
- IPEPS:ETH=1,SPEED=100; 86
- IPEPS:ETH=4,IPADDR=STANDBY2; 86
- • MMPTP - MML Port Print 89
- • MMLOP - MML Log Off Print 89
- • MMLOS - MML Log Off Set 89
- • MMPTC - MML Port Change 89
- Attributes 91
- Examples 91
- Output Format 91
- Chapter 6 Command Definitions 100
- RDC1=1,LABEL=ALARM; 102
- RDCRE:RECORD=,[DISCARD=Y]; 103
- RDCRE:RECORD=1; 103
- SGDPI:DEST=1, RAS=1; 108
- SGDPI:DEST=,RTPRI=,[LABEL=,]; 108
- SGDPI:DEST=,RAS=,[LABEL=,]; 108
- SGDPC:DEST=1, RAS=1; 109
- SGDPE:DEST=; 109
- SGDPE:DEST=1; 109
- SGDPP:[DEST=]; 109
- SGIRC:IR=1,DEST=5; 111
- SGIRE:IR=; 111
- SGIRE:IR=1; 111
- SGIRP:[IR=]; 111
- SNALI:RAS=,SEQ=,SNLINK=; 114
- SNALI:RAS=1,SEQ=1,SNLINK=1; 114
- SNRAE:RAS=; 116
- SNRAE:RAS=1; 116
- IPADDR2=192.112.111.123;; 119
- SNSLC:SNLINK=1, PPORT=2905; 120
- SNSLE:SNLINK=; 120
- SNSLE:SNLINK=1; 120
- STIPP:IPADDR=173.132.23.3; 128
- IP Status 128
- EXECUTED 128
- • Status 133
- • Stratum 133
- • Offset 133
- 193.145.185.151 135
- 173.132.73.122 135
- 173.132.73.21 135
- 193.145.185.149 135
- Signaling 137
- 193.145.185.154 138
- SGDPI:DEST=2,RTPRI=MTP; 141
- • itself 143
- • an IP address of 0.0.0.0 143
- 194.192.185.11 145
- 192.195.185.11 145
- 192.195.185.12 145
- 194.192.185.12 145
- RESET=Y,LABEL=C7LINK; 158
- RDPDE:REPORT=1,C7LINK=3; 158
- 194.192.185.111 166
- 195.193.185.12 167
- 195.193.185.11 167
- 195.193.185.111 167
- 11.3.2 SG 2 Configuration 168
- STTPP command 169
- Chapter 13: Command Summary 171
- Chapter 13 Command Summary 172
- Glossary 175
- Chapter 14 Glossary 176
Verwandte Produkte und Handbücher für Vernetzung Dialogic DSI SS7MD
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern